Sometimes, neighbors get confused about the fitguide selections about whether they have solid matte black flush rails, matte black and gloss black flush rails, or black and chrome flush rails on their 2019 Jeep Grand Cherokee. The Thule setup that uses Fit Kit for Thule Podium-Style Roof Rack Feet - 3142 # THKIT3142 are designed only to fit the black/chrome flush rails and the matte black/gloss black flush rails. If you solid matte black flush rails, this fit kit will not your Grand Cherokee,... view full answer...
The only modifications needed for the front of your 2021 Jeep Grand Cherokee Limited will be to the lower portion of the fascia at the bottom grill, where cut outs will be need to made for the base plate tabs and electrical bracket to sit when you are installing the Blue Ox Base Plate Kit # BX1128.
If you go to about the 34:45 mark of the linked installation video you can see the cut outs that will need to be made.
This will be the first part of your flat tow set up, and you'll also need... view full answer...
I would be happy to answer your questions about the Atwood Air Command Rooftop RV Air Conditioner - 11.3 Amps - 13,500 Btu - Ducted - Black item # AT15032-22. There is a fan button that allows you to switch between low, medium, high, and auto settings. The 11.3 amp is the average amps when the AC unit is running on cool. The amps can go up to 33 amps at start up. view full answer...
The torque rating for both the 1-7/8 inch and 2 inch hitch balls that are included in the etrailer.com Ball Mount Kit # 989900 is 250 foot-pounds. view full answer...
The wire that you are looking for is located behind or above the driver side kick panel. It is normally a light green wire. You may need to use installation kit # 5505 which has a 20 amp breaker or kit # 5506 which has a 30 amp breaker to complete installation of the brake controller power wire (black). Use # 5506 for up to 8 brakes.
I have linked a video that should help some. It is a different year vehicle and different brake controller but installation will still be very similar. view full answer...
Curt has designed the T-Connector Wiring Harness, # C56208, to work with the existing wiring of your 2015 Jeep Grand Cherokee. The 12 volt battery connection is designed to work with the unit to maximize performance and limit the strain on your vehicle's electrical system.
The 12 volt accessory circuit on some vehicles may not have a dedicated circuit and can not take the electrical load of both the trailer wiring harness and the 12 volt accessory plug. The result of this could cause overheating... view full answer...
According to my contact at Superchips, their TrailDash Performance Tuner will adjust itself to compensate for upgrades like a freer-flowing exhaust system, cold air intake or a larger throttle body. You should not need to adjust or update anything on the programmer itself, as these adjustments will be made automatically. view full answer...
Once installed, the 4-pole trailer connector would be stored in the cargo are of your Grand Cherokee. When needed, open the hatch and pull out enough of the connector and wiring to reach the connector on the trailer. Then, you can close the hatch on the wire. The rubber weather stripping around the hatch is plenty thick enough to cushion the wire and prevent it from being damaged, as long as you keep the wire well away from the latch. When you are finished using the connector, simply coil... view full answer...
Wire color used for the tail lights on any given vehicle is not always the same within the same model year of the same vehicle. Based on that you would have to test the wiring with a circuit tester like # 3808 if needed to find the function of the wiring. But it is unnecessary for your vehicle.
You need a wiring harness specifically made for a 2007 Jeep Grand Cherokee. You can use # 118425. It takes all of the guess work out and you will not have to test wiring or splice into the vehicle... view full answer...
The blue wire on the 4-Pole to 5-Pole Trailer Connector Adapter would need to be lengthened and tapped into the circuit that feeds the reverse lights on your Grand Cherokee. Simply locate the reverse lamp assembly, and find the wire feeding the bulb. This is where you would tap in the blue wire. You can use a Scotchlok connector, like part # SWC502905-1.
To view an install video, click on the provided link.The video shows the adapter being installed on a different vehicle, but the video... view full answer...
It is possible the wiring is already active on your 2012 Jeep Grand Cherokee, but you won't know until you install the # C55774. Once installed, test the connection to see if it is working. If not, you will need to go to the dealer and have them re-flash the computer to activate the tow package wiring circuit. view full answer...
So you can add a 7-way to your 2020 Jeep Grand Cherokee, but without the factory tow package/harness you won't be able to utilize the Hopkins 7- and 4-Pole Trailer Connector Socket # HM40975, which is what I believe you were referring to in regards to "spring loaded doors." The 4-way # 118384 you referenced is also something that plugs directly into the factory tow package and is unable to plug into a 4-way.
With out the factory tow package, to add a 7-way, the first thing needed is the... view full answer...
To install a trailer light, you will want to use part # C55369, a Curt T-Connector that is designed to work cooperatively with the vehicle computer and wiring. It plugs into a port in the cargo area, behind a panel on the driver side. I have added a link to the instructions below. view full answer...
The Draw-Tite Max-Frame Trailer Hitch Receiver, part # 75338 that is confirmed as a fit for your 2005 Grand Cherokee is installed right behind the bumper.
In the attached instructions there are 2 plastic pins that hold the bumper fascia onto the bumper that have to be removed first. Then you need to slide the fascia rearward about an inch to install the trailer hitch.
Since you have a trailer hitch already installed, you will need to make sure it is bolted on and that a replacement trailer... view full answer...
The torque specs for the Curt Trailer Hitch Receiver part # 13251 which is a fit for a 2008 Jeep Grand Cherokee can be found in the most up to date copy of the installation instructions which can be seen in the link attached for you below. The torque specs can change which is why you will need to refer to the link with an up to date copy of the instructions. If you need a torque wrench we do have some cost effective options for you like the Powerbuilt Beam-Type Torque Wrench part # ALL644044. view full answer...
I spoke with my contact in Technical Support at Curt Manufacturing, who tells me that their front mounted receiver would bolt to the underside of the front frame members and around the front stabilizer bar using with two of the connection points utilizing the existing holes for the stabilizer bar retaining bracket, as shown in the provided photo.
If the skid plate covers the mounting location and the retaining brackets, the skid plate would need to be removed in order to install the receiver.
To... view full answer...
To install the Tekonsha P2 Brake Controller, # 90885, on your 1994 Jeep Grand Cherokee, there are 2 possible options. If your Grand Cherokee has a factory installed 7-Way trailer connector at the rear of the vehicle, then you will just need to contact the brake controller wiring to the Jeep wiring located under the dash, driver side. You will need a circuit tester like # PTW2993 to test the vehicle wires for function.
The wire that has a constant signal is the 12-volt power wire and it... view full answer...
Sometimes Mopar used a light green wire, sometimes it was a blue wire. The fact that the wire you found has a tag on it positively identifies it as the brake output circuit.
I'd recommend the # 5506 Brake Controller Install Kit. I've linked you to a video showing the kit being used to install a different controller on a 2000 Grand Cherokee. The procedure on your vehicle would be very similar. The brake stoplight switch wire you'll need to attach the red brake controller wire to would be... view full answer...
The Curt T-Connector Custom Fit Vehicle Wiring, # C55369, is a T-Connector style connector meaning that it plugs into a plug on your 2001 Jeep Grand Cherokee. The connection point can be found behind the interior trim panel in the cargo area, on the driver's side. The converter box takes care of the necessary steps that need to be made to convert the signal from the 3-wire system on your Jeep to the 2-wire system used by most trailers. All you need to do is plug it in. I have included a... view full answer...
The T-One Vehicle Wiring Harness # 118727 is the right fit for your 2020 Jeep Grand Cherokee without the factory tow package, and I can definitely help you with some guidelines on how to install it. You also made a great choice with the Draw-Tite Trailer Hitch Receiver # 75699 for your Jeep, as it would have been my choice too because of its concealed look (I also added a link to a video install of the hitch on a Jeep for you to take a look at).
I have added a link to the installation... view full answer...
Go To Results